​Open: Mon, Thurs, Fri, Sat and Sunday

10 am - 4 pm


Appointments on Tuesdays and Wednesdays 


(feel free to ask for extended hours)



 ​ 916.859.0511​

  • Setting the time: press time + mode. Select the hour by either pressing the warm or cool button. Once the hour is correct, press mode, now you can adjust the minutes by either pressing the warm or cool buttons. Press time to lock it in. ​​​
  • Mode setting is either Standard, Economy or Sleep mode. Standard mode(Std)  means your hot tub will check the temperature every 30 minutes 24 hours a day. This mode uses the most electricity. Economy mode (Ecn) runs only during filtration times that you set. Sleep mode (Slp) will only heat the water to within 20 degrees of set temperature.

To change between the modes. Press mode to enter programming, then press cool to cycle through all 3 modes. Once your desired mode is visible on the screen, press mode to lock it in.

  • To program custom filter cycles (this is very important especially while using economy mode 'ECN'), press time + mode + mode + mode within 3 seconds. The PROGRAM, FILTER 1 and START TIME icons appear on the display. Press warm or cool to choose filter cycle 1 start time hour. Press mode to save the hour. Press warm or cool to choose the filter 1 start time minutes. Each press changes the start time by 5 minutes. Press mode to enter the minutes. Press mode to see PROGRAM, FILTER 1, and END TIME icons. Adjust the filter cycle 1 end time as outlined above using the warm or cool and mode buttons. Next, press mode to see PROGRAM, FILTER 2, and START TIME icons. Proceed as outlined above to enter the filter 2 start and end times. After the filter end time is entered, press mode to confirm the new filter cycle times into the system and display the current water temperature. Press time at any time during filter cycle programming sequence to save the values entered up to that point and exit programming.
  • Mode setting is either Standard, Economy or Sleep mode. Standard mode(Std)  means your hot tub will check the temperature every 30 minutes 24 hours a day. This mode uses the most electricity. Economy mode (Ecn) runs only during filtration times that you set. Sleep mode (Slp) will only heat the water to within 20 degrees of set temperature.
  • To change between the modes. Press mode to enter programming, then press cool to cycle through all 3 modes. Once your desired mode is visible on the screen, press mode to lock it in.
  • To adjust the filter cycles is it important to remember that there is no time clock to program. When you power up the hot tub this is the beginning of it's internal clock. Example, if it's 11:35 am and you just powered up the spa. This will always be the start time for filter cycle 1 (11:35am). Filter cycle 2 will automatically begin 12 hours from this time (11:35pm). Say you enjoy your tub at 8 pm most nights. Turn off the spa and turn it back on at 7pm. This will tell the spa to change the filter times to 7pm and 7 am. That way your spa will run 1 hour before you use it and will heat the water up before you use it.
  • To program the filter duration times. (Keep in mind filter duration is programmable for 1-12 hours. F1 means one hour, F2 means two hours, F3 means three hours etc...) Press warm + jets 1. Press warm to select the filter duration hours(F1-F12).
  • Press jets 1 to select the desired cycle. The display will show dn (day and night), d (day only), or n (night only).  Press jets 1 to select the desired program. Press jets 1 again to exit.
  • Mode setting is either Standard, Economy or Sleep mode. Standard mode(Std)  means your hot tub will check the temperature every 30 minutes 24 hours a day. This mode uses the most electricity. Economy mode (Ecn) runs only during filtration times that you set. Sleep mode (Slp) will only heat the water to within 20 degrees of set temperature.
  • To change between the modes. Press temp + light to enter programming. Press temp to cycle through all 3 modes. Press light to lock in your desired mode.
  • To adjust the filter cycles is it important to remember that there is no time clock to program. When you power up the hot tub this is the beginning of it's internal clock. Example, if it's 11:35 am and you just powered up the spa. This will always be the start time for filter cycle 1 (11:35am). Filter cycle 2 will automatically begin 12 hours from this time (11:35pm). Say you enjoy your tub at 8 pm most nights. Turn off the spa and turn it back on at 7pm. This will tell the spa to change the filter times to 7pm and 7 am. That way your spa will run 1 hour before you use it and will heat the water up before you use it.
  • To program the filter duration times. (Keep in mind filter duration is programmable for 1-12 hours. F1 means one hour, F2 means two hours, F3 means three hours etc...) Press temp + jets 1. Press temp to select the filter duration. Press jets 1 to select the number of cycles. The display will show dn (day and night), d (day only), or n (night only). Press temp to adjust. Press jets 1 to exit.

Bullfrog hot tub and spa programming cheat sheet - Sacramento

6 Button

8 Button

4 Button



Click Me For Directions

 ​ 916.859.0511​

Click Me For Directions
Hot Tubs and Spas Sacramento ga('create', 'UA-48500448-1', 'auto'); ga('send', 'pageview');