Programming your top end controller

4 Button Top End Controller
6 Button Top End Controller
8 Button Top End Controller
4 Button Top End Controller

4 button controller

  • Mode setting will be either Standard, Economy, or Sleep mode. You will choose which one you want. Standard mode (Std) means your hot tub will check the temperature every 30 minutes 24 hours a day. This mode uses the most electricity. Economy mode (Ecn) runs only during the filter times that you set. Sleep mode (Slp) will only heat the water to within 20 degrees of the set temperature. 
     

  • To change between modes, press Temp + light to enter programming. Press temp to cycle through all 3 modes. Press light to lock in your desired mode. 
     

  • To adjust the filter cycles it is important to remember that there is no time clock to program. Instead, when you power up your hot tub, the time in which you powered up your hot tub will be the first filter cylcle. Example: If it's 11:35 am and you just turned your spa on, this will always be the start time of filter cycle 1. Filter cycle 2 will automatically begin 12 hours later. In this case it will be 11:35 pm. Let's say you enjoy your hot tub around 8 pm most nights. Turn the spa off and then right back on at 7 pm. This will tell the spa that the new filter cycles are 7 pm and 7 am. This way your spa will automatically turn on at 7 pm and will run an hour before your normal time that you enjoy your hot tub. That way if the temperature dropped throughout the day, it will recover the heat for you beginning at 7 pm.
     

  • To program the filter duration times your can choose from 1-12 hours. F1 means 1 hour, F2 means 2 hours, F3 means 3 hours, F4 means 4 hours etc... Press temp + jet 1.  Press temp repeatedly until your desired F number is displayed.
     

  • Press jet 1 to select the number of cycles in a 24 hour period you want. The display will show dn (day and night), d (day only) or n (night only). Press temp to adjust. Press jet 1 to exit.

6 button controller

  • Mode setting will be either Standard, Economy, or Sleep mode. You will choose which one you want. Standard mode (Std) means your hot tub will check the temperature every 30 minutes 24 hours a day. This mode uses the most electricity. Economy mode (Ecn) runs only during the filter times that you set. Sleep mode (Slp) will only heat the water to within 20 degrees of the set temperature. 
     

  • To change between modes, press mode to enter programming. Press cool to cycle through all 3 modes. Press mode to lock in your desired mode. 
     

  • To adjust the filter cycles it is important to remember that there is no time clock to program. Instead, when you power up your hot tub, the time in which you powered up your hot tub will be the first filter cylcle. Example: If it's 11:35 am and you just turned your spa on, this will always be the start time of filter cycle 1. Filter cycle 2 will automatically begin 12 hours later. In this case it will be 11:35 pm. Let's say you enjoy your hot tub around 8 pm most nights. Turn the spa off and then right back on at 7 pm. This will tell the spa that the new filter cycles are 7 pm and 7 am. This way your spa will automatically turn on at 7 pm and will run an hour before your normal time that you enjoy your hot tub. That way if the temperature dropped throughout the day, it will recover the heat for you beginning at 7 pm.|
     

  • To program the filter duration times your can choose from 1-12 hours. F1 means 1 hour, F2 means 2 hours, F3 means 3 hours, F4 means 4 hours etc... Press warm + jet 1.  Press warm repeatedly until your desired F number is displayed.
     

  • Press jet 1 to select the number of cycles in a 24 hour period you want. The display will show dn (day and night), d (day only) or n (night only). Press temp to adjust. Press jet 1 to exit.

  • Mode setting will be either Standard, Economy, or Sleep mode. You will choose which one you want. Standard mode (Std) means your hot tub will check the temperature every 30 minutes 24 hours a day. This mode uses the most electricity. Economy mode (Ecn) runs only during the filter times that you set. Sleep mode (Slp) will only heat the water to within 20 degrees of the set temperature. 
     

  • To change between modes, press mode to enter programming. Press cool to cycle through all 3 modes. Press mode to lock in your desired mode. 
     

  • To program custom filter cycles (this is important especially while using economy mode (Ecn). Press time + mode + mode + mode within 3 seconds. The PROGRAM, FILTER 1 and START TIME icon appears on the display. Press warm or cool to choose the filter cycle 1 start time hour. Press mode to save the hour. Press warm or cool to choose the filter cycle 1 start time minute. Press mode to enter the minute. Press mode to see PROGRAM, FILTER 1 and END TIME icon. Adjust the filter cycle 1 end end time as outlinrd above using the warm or cool and mode buttons. Next, press mode to see PROGRAM, FILTER 2 and START TIME icon. Proceed as outlined above to enter the filter 2 start and end times. After the filter end time is entered, press mode to confirm the new filter cycle times into the system and displat the current water temperature. Press time at any time to save the values entered up to that point and exit programming.

8 button controller

  • Instagram
  • Yelp Social Icon
  • Facebook Social Icon
  • Twitter Social Icon
  • YouTube Social  Icon
  • Pinterest Social Icon
  • Houzz Social Icon